Cali-GrafCali-Graf
CompareDesignProductionPVWattsModeling

Production modeling: PVWatts defaults vs a detailed panel and inverter model — why numbers differ

Cali-Graf · Published Nov 18, 2026 · Data as of Nov 18, 2026

Two production estimates for the same roof can differ by several percent without either being wrong. In our engine, PVWatts with its default settings gave 1,638 kWh a year per kW of panels facing south at 20° in West Covina; the same four systems modeled with each panel's and inverter's own parameters gave 1,697 to 1,769 kWh per kW, 3.1% to 8.0% more across the two sites. The largest part of the gap is one setting: PVWatts assumes 14% system losses, the detailed model 10.5%, which alone adds 4.0%. The panel model adds another 0.8% to 2.7%, and the inverter model moves the result by -1.7% to 1.3%.

1,638
PVWatts defaults, kWh a year per kW, West Covina
South, 20°
4.0%
Output change from the loss setting alone
14% vs 10.54% losses
8.0%
Largest gap, detailed model vs PVWatts defaults
Four systems, two sites
In this guide
Three models, four systemsWhere the difference comes fromWhat to check when two estimates differData limitsQuestionsMethodologySourcesHow to cite this page

Three models, four systems#

SiteSystemPVWatts defaults, kWh per kWPanel model, kWh per kWPanel and inverter model, kWh per kWPanel model effectInverter model effectTotal vs PVWatts
West CovinaQ.PEAK DUO 410 on IQ8HC1,638.31,717.21,737.4+0.8%+1.2%+6.1%
West CovinaREC Pure-RX 460 on IQ8X1,638.31,750.51,768.8+2.7%+1.0%+8.0%
West CovinaLONGi 400 on IQ8PLUS1,638.31,717.71,696.9+0.8%−1.2%+3.6%
West CovinaJA Solar 405 on Powerwall 31,638.31,719.21,707.1+0.9%−0.7%+4.2%
LancasterQ.PEAK DUO 410 on IQ8HC1,861.01,951.01,976.8+0.8%+1.3%+6.2%
LancasterREC Pure-RX 460 on IQ8X1,861.01,985.32,007.1+2.6%+1.1%+7.9%
LancasterLONGi 400 on IQ8PLUS1,861.01,950.61,918.3+0.8%−1.7%+3.1%
LancasterJA Solar 405 on Powerwall 31,861.01,952.41,953.0+0.9%+0.0%+4.9%

Output per kW of panel rating for 12 panels facing south at 20°, typical-year weather at ZIP 91790 (West Covina) and ZIP 93535 (Lancaster). PVWatts defaults: a standard panel with a -0.37%/°C coefficient, 14% losses, a 96% inverter at DC/AC 1.2. Panel model: the panel's CEC single-diode parameters with the engine's 10.5% losses and the PVWatts inverter. Panel and inverter model: plus the inverter's CEC Sandia model. Panel model effect excludes the loss setting. Source: Cali-Graf engine.

Download this table (CSV)

Model the actual panel and inverter
Cali-Graf models each panel and inverter hour by hour from CEC data and shows where the energy goes.
Open Cali-Graf

Where the difference comes from#

- The loss setting. PVWatts' 14% default bundles soiling, shading, mismatch, wiring, connections, light-induced degradation, nameplate rating and availability. The engine uses 7.8% for the items that apply to its microinverter-based designs, plus a 3% shading allowance when no shading analysis is run. That choice alone moves the estimate by 4.0%, more than anything else here. - The panel. A specific panel's CEC parameters replace PVWatts' standard panel: its temperature coefficient, its behavior in low light and its rating. Panels with smaller temperature losses, such as the REC Pure-RX, gain the most. - The inverter. A microinverter that runs above PVWatts' flat 96% efficiency and rarely clips adds about a percent; one that clips on bright hours, such as an IQ8PLUS under a 400 W panel, takes about a percent or more away. A large hybrid inverter running at low load loses a little of its efficiency.

What to check when two estimates differ#

- Losses first. Compare the total loss percentage; a few points of losses explain most differences between tools. - Then the equipment. A tool that models the actual panel and inverter can differ from a generic model by a few percent either way. - Then the weather and shading. Different weather years and shading methods move results again, and are not compared here.

Data limits#

Four systems at two sites, all unshaded, facing south at 20°. The engine's loss setting is a modeling choice, not a measured value for any one home. The panel model effect is computed after removing the loss-setting effect by its ratio. Real systems also lose output to aging, which none of these single-year estimates include.

Why is my PVWatts estimate lower than my installer's?

In our runs the loss setting was the largest single difference: PVWatts assumes 14% losses by default; a model with 10.5% gives 4.0% more before any equipment difference. Check the loss percentage in both estimates first.

How much does the panel model matter?

In our four systems, 0.8% to 2.7% once the loss setting is set aside.

Is PVWatts accurate enough for a proposal?

It is a consistent, published method; its default losses make it conservative compared with a detailed model of the actual equipment, by 3.1% to 8.0% in our runs.

Methodology#

The Cali-Graf engine runs PySAM's PVWatts v8 with its defaults (standard module, 14% losses, 96% inverter efficiency, DC/AC 1.2, roof mount) and a detailed model in which each panel is the CEC single-diode model from its CEC parameters, the cell temperature comes from PVWatts' roof-mount model, and the inverter is the Sandia model with CEC parameters, per panel for microinverters. NSRDB typical-year weather at each ZIP. The loss-setting effect is (1 − 10.5%) ÷ (1 − 14%) − 1. Rounded half up.

Sources#

  1. NLR — PVWatts Calculator (Version 8). https://pvwatts.nlr.gov/
  2. NLR — PySAM, the Python package for the System Advisor Model. https://nrel-pysam.readthedocs.io/
  3. California Energy Commission — Solar Equipment Lists (PV modules and grid support inverters). https://solarequipment.energy.ca.gov/
  4. Sandia National Laboratories — Performance Model for Grid-Connected Photovoltaic Inverters (SAND2007-5036). https://www.osti.gov/biblio/920449
  5. NLR — National Solar Radiation Database (NSRDB), typical meteorological year. https://nsrdb.nlr.gov/

How to cite this page#

Cali-Graf. “Production modeling: PVWatts defaults vs a detailed panel and inverter model — why numbers differ.” cali-graf.com, updated Nov 18, 2026. https://cali-graf.com/guides/production-modeling-pvwatts-vs-pysam-vs-vendor-tools-why/