Cali-GrafCali-Graf
ReferenceBatteriesBackupEnphaseGenerators

Generator integration with solar and batteries: Enphase sizing rules

Cali-Graf · Published Nov 19, 2026 · Data as of Nov 19, 2026

Enphase sets a floor on the generator, not a ceiling. With IQ8 microinverters and IQ Battery 5P units, the generator's nameplate must be at least 100% of the microinverters' rated AC output or 143% of the batteries' power, whichever is higher: 10.98 kW for a system with two 5P batteries and 20 IQ8+ microinverters. The floor protects the generator from being back-fed by the solar and batteries. From 15 kWh of storage the floor exceeds what the generator port can use, 15.36 kW (64 A at 240 V), and a bigger generator charges the batteries no faster. Among the documents we reviewed, only Enphase's covers generators: the Tesla Powerwall 3 datasheet, which also covers Tesla's gateways, and the FranklinWH aPower 2 and aPower S and SolarEdge Home Battery datasheets do not mention them; FranklinWH's aGate and SolarEdge's backup equipment, where those systems connect to the home, were not reviewed. These rules are for the IQ Battery 5P: Enphase's planning guide for the newer IQ Battery 10C, which works with no IQ System Controller, says nothing about generators.

143%
Minimum generator, share of IQ Battery power
Enphase TEB-00004-8.0
15.36
Usable power of the generator port, kW
Enphase TEB-00004-8.0
10.98
Minimum generator for two IQ Battery 5P and 20 IQ8+, kW
Worked example
In this guide
Minimum generator by battery countThe rulesWorked examplesData limitsQuestionsMethodologySourcesHow to cite this page

Minimum generator by battery count#

IQ Battery 5P unitsStorage, kWhBattery power, kWMinimum generator nameplate, kW
153.845.49
2107.6810.98
31511.5216.47
42015.3621.96
84015.3621.96

Minimum generator nameplate rating for a battery-only system with IQ Battery 5P units, from Enphase's planning guide TEB-00004-8.0 (July 2026), Table 8; the battery power stops rising after four units because, with battery oversubscription, a System Controller battery port is rated at 15.36 kW. With solar, the solar rule below applies too.

Download this table (CSV)

Size the backup system around the loads
Cali-Graf sizes the battery for the backed-up loads and models the bill hour by hour.
Open Cali-Graf

The rules#

- Solar only (Sunlight Backup). The generator must be at least 100% of the microinverter array's rated AC output. - Battery only. At least 143% of the IQ Battery array's power: each IQ Battery 5P is 3.84 kW. - Solar and battery with IQ8 microinverters. The higher of the two. - Solar and battery with IQ6 or IQ7 microinverters. 143% of the battery power only. With M Series microinverters there is no solar-to-generator ratio, because they are disconnected from the microgrid while the generator runs. - Size for the loads too. Enphase asks for a generator big enough to run the loads while charging the batteries, and for batteries big enough to carry the backed-up loads until the generator connects, with load control shedding what they cannot carry. - Smaller is risky. The Enphase Installer App accepts a smaller generator, but Enphase warns it may compromise the microgrid's stability and damage the generator through back-feed. - Equipment. The generator connects to the IQ System Controller 3G's generator port (64 A continuous), with Enphase generator CTs; solar may need to be shed for stability.

Worked examples#

SystemMicroinverter output, kWBattery power, kWMinimum generator, kWSet by
20 IQ8+ (290 W in the guide) and two IQ Battery 5P5.807.6810.98Battery
30 IQ8HC (384 VA) and two IQ Battery 5P11.527.6811.52Solar
30 IQ8HC (384 VA) and one IQ Battery 5P11.523.8411.52Solar

Minimum generator nameplate under Enphase's rule for systems with IQ8 microinverters and IQ Battery 5P; the IQ8+ at the 290 W Enphase uses in its own tables, the IQ8HC at its data-sheet 384 VA. "Set by": which side of the rule is larger.

Download this table (CSV)

- Small solar, two batteries: the batteries set the floor. - Large solar: the microinverters set it, and adding batteries does not raise it until their 143% exceeds the solar.

Data limits#

Rules are Enphase's planning guide as of July 2026; the generator maker's manual, the electrical code and the building department also apply. Enphase's planning guide for the IQ Battery 10C and IQ Combiner 6C (TEB-00282-4.0, February 2026) has no generator content, so these rules do not cover a 10C system; the 10C made up 25% of the Enphase battery systems in SCE's Los Angeles County territory from January to August 2026, according to our 5P and 10C guide. The Tesla, FranklinWH and SolarEdge datasheets reviewed here do not cover generators, and the documents for FranklinWH's aGate and SolarEdge's backup equipment were not reviewed, so these makers' rules are not compared; it does not follow that their systems cannot use a generator. Interconnection records do not show generators.

What size generator do I need with Enphase batteries?

At least 143% of the batteries' power or 100% of the microinverters' output, whichever is higher; for two IQ Battery 5P units and a modest array, 10.98 kW.

Can I connect a generator to an IQ Battery 10C system?

Enphase's 10C planning guide does not cover generators, and the 10C does not work with the IQ System Controller 3G, which has the generator port; ask Enphase before planning one.

Is a bigger generator better?

Only up to the generator port: with 15 kWh of batteries or more, the floor already exceeds the 15.36 kW the port can use, and a bigger generator does not charge faster.

Can I use a small portable generator?

Enphase allows it in the app but warns that a generator below the minimum may destabilize the system and be damaged by back-feed.

Methodology#

Each rule and table row was checked word for word in Enphase's technical brief TEB-00004-8.0 (July 2026); the examples apply its rule for IQ8 microinverters with IQ Battery 5P. The Tesla Powerwall 3, FranklinWH aPower 2 and aPower S and SolarEdge Home Battery 400V datasheets were searched for generator content and have none.

Sources#

  1. Enphase — Planning the Enphase Energy System, technical brief TEB-00004-8.0 (July 2026), section 6.2.2.5 Generator sizing. https://enphase.com/download/planning-enphase-energy-system-tech-brief
  2. Enphase — IQ8HC Microinverter data sheet, DSH-00047-10.0 (July 2026). https://enphase.com/download/iq8hc-microinverter-data-sheet
  3. Tesla — Powerwall 3 Datasheet (2025). https://energylibrary.tesla.com/docs/Public/EnergyStorage/Powerwall/3/Datasheet/en-us/Powerwall-3-Datasheet.pdf
  4. Enphase — Enphase Energy System planning with IQ Battery 10C/10CS and IQ Combiner 6C, technical brief TEB-00282-4.0 (February 2026). https://www.invertersupply.com/media/data/teb-00282-en-us-ees-iq-bat-10c-10cs-iq-comb-6c.pdf
  5. FranklinWH — aPower 2 Datasheet. https://www.franklinwh.com/document/apower-2-datasheet
  6. FranklinWH — aPower S Datasheet.
  7. SolarEdge — SolarEdge Home Battery 400V for North America, datasheet DS-000167-NAM (March 5, 2024).

How to cite this page#

Cali-Graf. “Generator integration with solar and batteries: Enphase sizing rules.” cali-graf.com, updated Nov 19, 2026. https://cali-graf.com/guides/generator-integration-with-solar-and-batteries/